Skip to content
Menu

Inverse Cup and Handle Pattern

By Chad Smith, Director of Research & Analysis · Updated

On this page
  1. What it is
  2. How to identify it
  3. What it suggests and in which context
  4. How traders use it
  5. Limitations and false signals
  6. Similar patterns
CupHandleRim
Illustration, not real price data

The inverse cup and handle is a bearish chart pattern. Price rises and falls in a rounded, upside-down U that forms the cup. It then bounces slightly in a short, shallow move that forms the handle. When price breaks below the cup's base, the pattern suggests the decline is resuming.

What it is

The inverse cup and handle is the mirror image of the cup and handle. It describes a slow, orderly consolidation within a downtrend.

After a decline, the market rallies. Instead of a sharp spike, it forms a rounded top: buying fades gradually, the market moves sideways near the highs, and selling slowly returns until price falls back to the level where the rally began. That level, the base of the inverted cup, acts as support.

At the base, some traders who sold short before the rally buy back to break even, and bargain hunters step in. That buying creates the handle: a small bounce, often drifting slightly higher or sideways. When the handle fails and price breaks below the base, the last buyers have been exhausted and the downtrend can continue.

The pattern has two parts:

  • The cup. A rounded, upside-down U, with the two sides ending near the same level.
  • The handle. A short, shallow bounce near the right side, often shaped like a small bear flag.

The inverted cup alone looks like a rounding top, but the rounding top is a reversal after an advance, while the inverse cup and handle is usually taught as a continuation within a decline.

How to identify it

  1. Prior downtrend. The pattern is usually a pause within a decline.
  2. Rounded inverted cup. A gradual rise and fall, not a sharp spike.
  3. Moderate height. The cup should not recover most of the prior decline.
  4. Base at similar levels. The left and right sides of the cup end near the same price, which forms support.
  5. Shallow handle. A small bounce near the right side, much smaller than the cup.
  6. Breakdown. Price closes below the base, or below the handle's lower line.

Volume. The classic description shows volume fading near the top of the cup and rising on the breakout below the base.

What it suggests and in which context

An inverse cup and handle suggests that a rally within a downtrend has been absorbed by sellers. The rounded top shows gradual distribution, and the weak handle shows little remaining demand near the base.

It carries more weight when:

  • The prior trend is down. The pattern fits best as a continuation.
  • The cup is smooth. A rounded shape shows a steady change in sentiment.
  • The handle is small. A weak bounce shows little buying at the base.
  • The breakdown is decisive. A strong close below the base is more convincing.
  • It forms on a higher timeframe. Larger patterns reflect longer periods of selling.

Use it within your wider technical analysis.

How traders use it

Entry. The standard entry is a close below the base or the handle's lower line. Some traders sell within the handle in anticipation, using the handle's high as a stop.

Stop. A typical stop-loss goes above the handle's high. A wider stop sits above the midpoint of the cup.

Target. The measured move takes the cup's height, from base to top, and subtracts it from the breakdown level. Traders also check nearby support. Compare with the risk-reward ratio.

For long positions. Traders holding longs from the rally inside the cup often use the base as their exit level.

Worked example (illustration only). Say AUD/USD falls to 0.6500, then rallies in a rounded curve to 0.6700 over several weeks and gradually declines back to 0.6510. It bounces to 0.6560 in a small handle, then falls and closes at 0.6490, below the base. The cup's height is 200 pips, so the measured target is about 0.6290. A trader selling at 0.6490 with a stop at 0.6565, above the handle, risks 75 pips for a potential 200.

Inverse cup at a top. When the pattern forms after a long advance rather than within a decline, it works more like a rounding top with a final bounce. The trading logic is the same, but the breakdown marks a change of trend rather than a continuation, and traders may choose a more conservative target.

Common mistakes. Treating any rounded rally and decline as the pattern, without a clear base and handle, is common. Another is selling at the base before the handle has formed, which often runs into the buying that creates the handle.

Reading the handle's shape. The handle often looks like a small rising flag or wedge. A handle that stalls quickly and stays tight shows weak demand at the base, which supports the bearish case. A handle that rallies strongly back toward the top of the cup suggests buyers are still active, and the pattern may be failing.

Limitations and false signals

  • Long formation. The cup can take a long time, testing the patience of early traders.
  • Strong handles. A handle that recovers much of the cup suggests the pattern is failing.
  • False breakdowns. Price can close below the base and recover.
  • Subjective shape. Deciding what counts as rounded is a judgment call.
  • Approximate targets. The cup-height projection is a guide only.

Similar patterns

Brokers with strong charting to practice on

Put this into practice on a demo account first, with no money at risk.

Frequently asked questions

What is an inverse cup and handle?

It is a bearish chart pattern with a rounded, upside-down U shape (the cup) followed by a small, shallow bounce (the handle), and then a break below the cup's base.

Is the inverse cup and handle a continuation pattern?

It is mostly taught as a bearish continuation within a downtrend. When it forms after a long advance, some traders treat it as a topping pattern instead.

How deep should the handle be in an inverse cup and handle?

The handle should be a small bounce near the right side of the cup, recovering only a modest part of the cup's height.

What is the target for an inverse cup and handle?

Traders usually measure the cup's height from its base to its top and subtract that distance from the breakdown level.