Skip to content
Menu

Parabolic SAR

By Chad Smith, Director of Research & Analysis · Updated

On this page
  1. What it measures
  2. The formula
  3. Default settings
  4. How to read it
  5. Parabolic SAR vs Supertrend and moving averages
  6. Common strategies
  7. Weaknesses
  8. Indicators it pairs with
SAR (0.02, 0.2)
Illustration, not real price data

The Parabolic SAR is a trend-following indicator that plots a series of dots above or below price. J. Welles Wilder introduced it in 1978. SAR stands for "stop and reverse": in an uptrend the dots trail below price and act as a rising stop, and when price crosses them the indicator flips to the other side and starts trailing from above. The dots accelerate as a trend extends, which gives the curve its parabolic shape.

What it measures

The Parabolic SAR measures where a trailing stop should be, given how long a trend has run and how far it has moved. It is less a measure of a market property, like volatility or momentum, and more a rule for following a trend and exiting when it fails.

It assumes the market is always in a trend. When a trend begins, the stop sits some distance away. As price makes new extremes, the stop moves closer faster, because the acceleration factor increases. The idea is that a mature trend needs less room, and that time works against a position that is not moving.

The formula

SAR(tomorrow) = SAR(today) + AF × (EP − SAR(today))

where
  EP = extreme point: the highest high of the current uptrend,
       or the lowest low of the current downtrend
  AF = acceleration factor
       starts at 0.02
       rises by 0.02 each time a new EP is set
       capped at 0.20

Rules:
  In an uptrend, SAR cannot be above the lows of the last two bars.
  In a downtrend, SAR cannot be below the highs of the last two bars.
  When price crosses SAR, the trend flips:
    the new SAR is set to the prior EP,
    AF resets to 0.02,
    and EP resets to the current bar's extreme.

Worked example (illustrative numbers). In an uptrend, today's SAR is 98.00 and the highest high so far (EP) is 104.00. AF is 0.06 after two new highs. Tomorrow's SAR = 98.00 + 0.06 × (104.00 − 98.00) = 98.00 + 0.36 = 98.36. If price makes a new high of 105.00 tomorrow, EP becomes 105.00 and AF rises to 0.08, so the next SAR moves faster: 98.36 + 0.08 × (105.00 − 98.36) = 98.36 + 0.53 = 98.89. If price instead falls through 98.36, the SAR flips above price and starts at the prior EP of 104.00, with AF reset to 0.02.

Default settings

SettingConventional value
AF start0.02
AF step0.02
AF maximum0.20

A lower step makes the SAR slower and less sensitive, so it flips less often. A higher step makes it tighten faster and flip more often. The Parabolic SAR is built into MetaTrader, TradingView and other standard charting platforms.

How to read it

Dot position. Dots below price show uptrend mode; dots above show downtrend mode. The indicator is always in one mode or the other.

Flips. When price touches or crosses the dots, they flip. In Wilder's original system, that is the signal to close the current position and open one in the other direction.

Spacing. Early in a trend, the dots sit far from price and move slowly. As the trend extends, they speed up and close in. Tightly spaced dots near price show a trend that needs to keep moving to avoid being stopped.

No middle ground. The SAR has no neutral reading. It cannot say "the market is ranging", which is the root of its main weakness.

Parabolic SAR vs Supertrend and moving averages

Supertrend also flips between above and below price, but it sets its distance with ATR and does not accelerate over time. Supertrend's distance changes with volatility, while the SAR's distance shrinks with the age and extent of a trend.

A moving average used as a trailing stop moves at a steady pace set by its period. The SAR starts loose and becomes tighter. In long, steady trends, the SAR can stop a trader out earlier than a moving average would; in sharp, short trends it can lock in more of the move.

Common strategies

Trailing stop

Many traders use the SAR only as an exit. They enter with another method and then move the stop-loss to the SAR value each bar. When price hits the dots, the position closes.

Stop and reverse

Wilder's full system always holds a position, flipping long and short on every reversal. This works in markets with long trends and fails in ranges, so it is rarely used without filters today.

Trend-filtered entries

Combine the SAR with a trend filter such as ADX above 25 or price above a 200-period moving average. Only take SAR flips in the direction of the filter, and ignore flips against it.

Confirmation with momentum

A SAR flip that coincides with a MACD cross or an RSI move through 50 carries more weight than a flip alone.

Weaknesses

The SAR whipsaws in ranges. Because it always assumes a trend, sideways price action causes frequent flips, each of which is a losing signal in a stop-and-reverse system.

Its acceleration is fixed. The AF rises with new extremes regardless of volatility, so in a volatile trend the stop can tighten too quickly and close a position on a normal pullback.

Flips are late at major turns. The dots trail price, so the reversal signal comes only after price has already moved against the prior trend.

The SAR value depends on where the calculation started. Different chart histories can show slightly different dots early in a series.

Indicators it pairs with

  • ADX, to trade SAR signals only when a trend is present.
  • Moving averages, to define direction and filter out counter-trend flips.
  • ATR, to check whether the SAR stop distance makes sense for current volatility.
  • MACD or RSI, for momentum confirmation of flips.
  • Supertrend, as an alternative trailing method based on volatility.

To understand trend-following tools and exits in more depth, see the technical analysis course.

Brokers with strong charting to practice on

Put this into practice on a demo account first, with no money at risk.

Frequently asked questions

What does SAR stand for?

SAR stands for stop and reverse. Wilder designed it as a system that is always in the market, closing a long and opening a short when the dots flip, and the reverse.

What are the standard Parabolic SAR settings?

The standard settings are an acceleration factor starting at 0.02, rising by 0.02 each time a new extreme is made, up to a maximum of 0.20.

How do you read Parabolic SAR dots?

Dots below price mean the indicator is in an uptrend mode, and dots above price mean downtrend mode. When price crosses the dots, they flip to the other side.

Why does Parabolic SAR give so many false signals?

It always assumes a trend exists. In sideways markets price crosses the dots often, which flips the indicator back and forth.

Is Parabolic SAR good for stop placement?

Many traders use it as a trailing stop in trending markets because it tightens as the trend continues. It works poorly when the market is ranging.