Supertrend Indicator
By Chad Smith, Director of Research & Analysis · Updated
On this page
Supertrend is a trend-following indicator that draws a single line below price in an uptrend and above price in a downtrend. The line's distance from price is set by the Average True Range, so it adapts to volatility. When price closes through the line, the indicator flips sides and changes color. Its simplicity has made it popular with short-term traders, especially in stock index and crypto markets. It is commonly credited to Olivier Seban.
What it measures
Supertrend measures the current trend direction and a volatility-adjusted level at which that direction would be considered broken. In an uptrend, the line acts as a trailing stop-loss level. In a downtrend, it acts as a trailing resistance level.
The line is built from the bar's midpoint, plus or minus a multiple of ATR. Because ATR expands in volatile markets, the line moves farther from price when conditions are wild and closer when they are calm. That gives trends room to breathe without fixed distances.
Supertrend only ever reads "up" or "down". It has no neutral state, which is both its appeal and its main weakness.
The formula
Midpoint (HL2) = (High + Low) / 2
Basic upper band = HL2 + Multiplier × ATR(N)
Basic lower band = HL2 − Multiplier × ATR(N)
Final upper band:
If basic upper < previous final upper, or previous Close > previous final upper:
final upper = basic upper
Otherwise: final upper = previous final upper
Final lower band:
If basic lower > previous final lower, or previous Close < previous final lower:
final lower = basic lower
Otherwise: final lower = previous final lower
Supertrend:
In an uptrend, Supertrend = final lower band
In a downtrend, Supertrend = final upper band
Flip to downtrend when Close < final lower band
Flip to uptrend when Close > final upper band
Defaults: N = 10, Multiplier = 3
The "final band" rules are what make the line one-directional. In an uptrend the lower band can rise but never fall, so it ratchets up behind price.
Worked example (illustrative numbers). A bar has a high of 104 and a low of 100, so HL2 is 102. ATR(10) is 1.5. With a multiplier of 3, the basic lower band is 102 − 4.5 = 97.5. If the previous final lower band was 96.8, the new final lower band rises to 97.5. Supertrend reads 97.5. If on a later bar price closes at 97.0, below the current final lower band, the indicator flips to downtrend and the line jumps above price to the final upper band.
Default settings
| Setting | Conventional value |
|---|---|
| ATR period | 10 |
| Multiplier | 3 |
| Source | HL2 |
A lower multiplier, such as 2, hugs price more closely and flips more often. A higher multiplier, such as 4, gives fewer flips but larger give-backs. Supertrend is built into TradingView; on MetaTrader it is widely available as a custom indicator.
How to read it
Color and position. A line below price, usually green, means uptrend mode. A line above price, usually red, means downtrend mode.
Flips. A change of side is the main signal. It occurs on a close beyond the line, not just an intrabar touch.
Flat sections. When the line goes flat in an uptrend, the lower band is not rising because volatility or price has not pushed it higher. Price pulling back toward a flat line is a test of the trend.
Distance. A large gap between price and the line shows an extended move relative to volatility. A small gap shows price is close to flipping the indicator.
Supertrend vs Parabolic SAR and Keltner Channels
Parabolic SAR also trails price and flips, but its distance shrinks as a trend continues because of its acceleration factor. Supertrend's distance follows ATR instead. In a long, steady trend, the SAR tends to catch up with price and stop out sooner; Supertrend stays a constant volatility distance away.
Keltner Channels use ATR around an EMA and show both upper and lower bands at all times. Supertrend uses ATR around the bar midpoint and shows only one band, the one relevant to the current trend, with the one-way ratchet rule.
Chandelier exits work similarly but measure the ATR distance from the highest high or lowest low since entry, rather than from the midpoint.
Common strategies
Flip entries
Buy when Supertrend flips to uptrend and sell when it flips to downtrend. This always keeps a position on, much like a stop-and-reverse system. It works in trends and struggles in ranges.
Trend filter with other entries
Use Supertrend only to decide direction. Take long setups from price action or oscillators only while Supertrend is in uptrend mode, and shorts only in downtrend mode.
Trailing stop
Enter with any method, then trail the stop along the Supertrend line. When price closes through it, exit.
Multiple Supertrends
Some traders plot two or three Supertrends with different settings. Trades are taken only when all agree, which reduces signals but filters out many false flips.
Weaknesses
Supertrend whipsaws in ranges. With no neutral state, sideways price action causes repeated flips, each one a potential loss.
It is lagging. A flip requires a close beyond an ATR band, so it happens after a meaningful move against the old trend.
Volatility spikes widen the band. After a sharp news bar, ATR rises and the line jumps farther away, which can leave a trailing stop far from price.
Settings matter. Small changes in multiplier or period can change the number of flips noticeably, and tuning them to past data can be misleading.
Indicators it pairs with
- ADX, to trade flips only when a trend has strength.
- Moving averages, for a slower trend filter.
- RSI or MACD, to confirm momentum around flips.
- ATR, which sets the Supertrend distance and helps with position sizing.
- Volume tools such as OBV, to confirm participation behind a new trend.
For more on trend-following and trailing exits, see the technical analysis course.
Brokers with strong charting to practice on
Put this into practice on a demo account first, with no money at risk.
- Featured broker
Pepperstone4.7 / 5Visit
IC Markets4.9 / 5Visit
GO Markets4.8 / 5Visit
Frequently asked questions
How does the Supertrend indicator work?
It places a line a multiple of ATR below price in an uptrend or above price in a downtrend. When price closes through the line, the indicator flips to the other side.
What are the default Supertrend settings?
The most common defaults are an ATR period of 10 and a multiplier of 3. Some traders lower the multiplier for faster signals or raise it for fewer flips.
Is Supertrend a leading or lagging indicator?
It is lagging. It reacts after price has moved far enough to close beyond the ATR band, so it confirms trends rather than predicting them.
How is Supertrend different from Parabolic SAR?
Both trail price and flip on reversals. Supertrend sets its distance from ATR, so it adapts to volatility, while Parabolic SAR tightens with an acceleration factor as a trend ages.
Can the Supertrend line move against the trend?
No. In an uptrend the line can only rise or stay flat, and in a downtrend it can only fall or stay flat, until a flip occurs.